What Is The Final Step In The Lockout Procedure Before Servicing May Begin

Release from Lockout/Tagout

Basic Steps for Release from Lockout/Tagout

LOTO

LOTO follows an equipment-specific procedure.

OSHA's Lockout/Tagout standard includes requirements for releasing machines or equipment that take been locked out or tagged out prior to restoring energy to the equipment and using it.

Before lockout or tagout devices are removed and energy is restored, there are some procedures the authorized employee must follow:

The work area must start exist inspected to ensure that nonessential items (due east.g., tools, spare parts) take been removed and that all of the machine or equipment components are operationally intact.
The work area must and so be checked to ensure all workers take been safety positioned or have cleared the area. In addition, all affected workers must exist notified that the lockout or tagout devices have been removed before the equipment is started.
Each lockout or tagout device must be removed from the energy-isolating device by the employee who applied the device.

i. Earlier lockout or tagout devices are removed and energy restored, what must the authorized employee do first?

a. Articulate the area of all essential workers
b. Inspect and clear the area of non-essential items
c. Remove alert signs
d. Install energy-isolating devices

Next Section

Absence of the Authorized Employee

LOTO

Make certain you endeavour to contact the authorized employee who performed LOTO.

If the authorized employee who affixed lockout/tagout devices is not present, you can authorize another employee to remove the device if that employee is properly trained and follows a documented energy control process. The procedure must ensure that the original authorized employee is not available to remove the device, that someone has tried to contact and inform the authorized employee that another employee has removed the device, and that the authorized employee knows the device has been removed before returning to work. To ensure prophylactic startup, the equipment should also exist inspected and affected employees notified.

Here'south what must be washed if a worker who didn't use the lockout/tagout device actually removes the device. The person in charge must accomplish three deportment listed below:

Verify that the authorized employee who applied the device is not at the facility.
Make all reasonable efforts to contact the authorized employee to inform him/her that his/her lockout or tagout device has been removed.
Ensure that the authorized employee knows that the lockout device has been removed before he/she resumes work at the facility.

Best Practice: Some companies take developed a "Lock Removal Course" and require information technology to be completed before a lock is removed by some other authorized employee. This form identifies the lock owner and equipment, how the possessor was contacted, the reason information technology was left on, confirmation the job was complete, why the lock is beingness removed, and actions taken to ensure prophylactic startup. The form is signed past a supervisor and kept on file for annual review.

2. Which of the following is a condition that must be met if some other authorized employee actually removes the device?

a. The other authorized employee must evidence his or her authorization bill of fare
b. Verify that the authorized employee who practical the LOTO device is not present
c. Brand an try to tell the supervisor that the LOTO device has been removed
d. Ensure the supervisor knows the LOTO device has been removed

Next Section

Testing Mechanism or Equipment

LOTO

Total release and entry back into lockout/tagout is required when testing.

In some circumstances, workers demand to temporarily restore free energy to a machine or piece of equipment during servicing or maintenance to test and /or reposition the car or piece of equipment.

Written energy control procedures will address the temporary removal of lockout or tagout devices. Temporary removal is allowed when re-energizing equipment is necessary, for instance, when power is needed to test or position the equipment. This applies but for the limited time required to perform the task and the procedure must be documented.

Although lockout/tagout devices may be removed temporarily to perform testing, information technology is important to know that you lot may not use an abbreviated procedure during the release - test - restore sequence. You must utilise full lockout/tagout procedures anytime you release from lockout/tagout or restore equipment afterwards testing and positioning.

3. Which type of modification may be made to lockout/tagout entry or release procedures for testing purposes?

a. Temporary removal of i energy-isolation device may be made for testing
b. None - total lockout/tagout procedures must be used for testing
c. An abbreviated entry and release from the lockout/tagout status may be fabricated
d. OSHA does not have a position with regard to testing during lockout/tagout

Next Section

Temporary Removal Procedures

LOTO

Be sure to follow LOTO procedures for temporary testing.

Below is the sequence of action that must occur in the temporary removal of the lockout/tagout devices:

The car or equipment must be cleared of tools and materials.
Workers must be removed from the machine or equipment expanse.
All lockout or tagout devices may then be removed.
Authorized workers may then go on to energize and exam or position the equipment or machinery.
Following testing or positioning, all systems must be de-energized and energy control measures reapplied to continue the servicing and /or maintenance.

4. During lockout/tagout, which of the following actions should occur before authorized workers go on to energize and examination or position equipment or mechanism?

a. Articulate tools and materials from the auto or equipment
b. Verify workers are at to the lowest degree ten feet from the machine or equipment expanse
c. De-energize and then reapply energy control measures
d. Affix lockout or tagout devices prior to testing

Adjacent Section

Release subsequently Long-Term Shutdown

LOTO

What can happen if release from long-term LOTO does not include making sure equipment is operating correctly.

Yous should accept an additional energy-control procedure to protect workers if they must restart equipment after long-term shutdowns. Make certain you do the following:

Determine who will be responsible for monitoring any lockout and tagout devices that control free energy to the equipment.
Include steps in the procedure for protecting workers if they need to remove or change parts while the equipment is close downwards.
Do non restart equipment until you are admittedly certain that information technology is working properly.

five. If in that location has been a long-term shutdown of equipment or machinery, what action should you take prior to startup?

a. Be admittedly certain the equipment is working properly
b. Become permission from the safety officeholder to perform startup
c. Decide the appointment and time shutdown occurred
d. Coordinate startup activities with the safety department

Check your Piece of work

Click on the "Bank check Quiz Answers" button to grade your quiz and see your score. You lot will receive a bulletin if you forgot to answer i of the questions. Afterward clicking the button, the questions you missed will be listed below. Yous tin can correct any missed questions and recheck your answers.

Video

FAQ on LOTO Video - HSEBox

In this video, HSE Box presents 10 questions and answers regarding Lockout/Tagout (LOTO).

Next Module